What are the settings on an insulin pump?

The four main settings that need to be programmed into an insulin pump are: basal dosing (basal rates) bolus dosing (insulin-to-carbohydrate ratio) blood glucose correction settings (insulin sensitivity factor also known as the correction factor)

How do I adjust my insulin pump?

Adjusting insulin when using an insulin pump

  1. High blood sugar levels for three days in a row at the same time of the day; increase insulin dose.
  2. Low blood sugar levels for two days in a row at the same time of the day; decrease insulin dose.

What should my insulin sensitivity factor be?

According to the ADA, the target level should be as close as possible to the levels that a person without diabetes would have. These are: Between 70–130 mg/dL before a meal. No higher than 180 mg/dL up to 2 hours after a meal.

What is sensitivity on an insulin pump?

Did You Know: Your insulin sensitivity is the amount that your blood glucose (BG) level is reduced by one unit of insulin. This value is used to calculate a suggested insulin dose to correct a high BG. Because this sensitivity may vary throughout the day, your insulin pump lets you set up to 8 sensitivity settings.

IT IS IMPORTANT:  Can diabetes make you mentally unstable?

How do you set up basal rate of insulin pump?

Changing Your Basal Rate(s)

  1. Go to the SET BASAL RATE 1 screen. …
  2. The SET BASAL RATE 1 screen flashes the basal rate in U/H.
  3. Enter your first basal rate amount and press ACT. …
  4. The SET START TIME 2 screen appears. …
  5. In the SET START TIME 2 screen, enter the start time for the next rate.
  6. Press ACT. …
  7. Press ACT.

How long does it take to adjust to insulin pump?

FINE-TUNE THE PUMP PARAMETERS

It is a three-part process and may take up to a week for each part. The three parts are: • Testing and adjusting the basal rate. Testing and adjusting the meal bolus.

What is a normal insulin correction factor?

Regular insulin

This equals 50. This means your insulin sensitivity factor is 1:50, or that one unit of regular insulin will lower your blood sugar by about 50 mg/dL.

What is the normal range for insulin resistance?

A waist measurement of 40 inches or more for men and 35 inches or more for women is linked to insulin resistance. This is true even if your body mass index (BMI) falls within the normal range. However, research has shown that Asian Americans may have an increased risk for insulin resistance even without a high BMI.

How much glucose does 1 unit of insulin reduce?

Generally, to correct a high blood sugar, one unit of insulin is needed to drop the blood glucose by 50 mg/dl. This drop in blood sugar can range from 30-100 mg/dl or more, depending on individual insulin sensitivities, and other circumstances.

IT IS IMPORTANT:  Which nutrient is the true cause of diabetes?

What is insulin to carb ratio?

Insulin to Carb Ratio (ICR) equals the number of grams of carbohydrate that 1 unit of rapid-acting insulin will cover.

How do you set a carb ratio?

Start by decreasing the grams of carb in your ratio by 1 or 2. For example: If your CIR was 15 grams for every 1 unit of insulin, change the ratio to 14 or 13 grams of carbohydrate for every 1 unit of insulin. insulin, so use a larger CIR. Start by increasing the grams of carbohydrate in your ratio by 1 or 2.

Can you be too sensitive to insulin?

For people with type 1 diabetes, having high insulin sensitivity can sometimes increase the risk of hypoglycemia If you are particularly sensitive to insulin, there are insulin pens which can give half units and could help to reduce the risk of going hypo.

How is insulin sensitivity measured?

(2001) Score for measuring the Insulin Sensitivity Index: The ISI is calculated for fat-free body mass by dividing the glucose disposal rate (M – mg/kg/min) by the average plasma insulin concentration over the final 60 minutes of the 120 minute test. An ISI of 6.3 M/mU/l defined individuals with insulin resistance.

What percentage of insulin should be basal?

Consider the norms (but don’t live by them).

For most people, 40-50% of the total insulin for the day is basal insulin.

When do you adjust basal or bolus insulin?

Consider adding bolus insulin once basal dose starts exceeding 0.5 units/kg (e.g. if 90.0 kg and taking more than 45 units basal insulin). Refer to Insulin Formulas.

IT IS IMPORTANT:  How long does Lantus take to peak?

What is the average basal rate?

Most people run their basals for 4-6 hours, which means your active basal profiles have about 4 to 6 basal rates. Though, we do see a lot of variance across all age groups.